Series 1 - 4 Extruded Aluminium Enclosures

Series 1 - 4 Extruded Aluminium EnclosuresThe Series 1 - 4 Enclosures are manufactured and customised in the United Kingdom. The Series 1 - 4 Enclosures are available in standard extrusion lengths of 40mm, 80mm, 120mm, 160mm and 220mm we can also offer any custom extrusion lengths required. The width and height vary from series to series, a full list of dimensions can be found below. The Series 1 - 4 Enclosures are available in either black, pre-anodised black, blue, red or silver with any custom colour required for both the extrusion and end plates. Minimum order quantities apply for blue, red and custom colours of 10 pieces, whilst with black, pre-anodised black and silver the minimum order quantity is 1 piece. The extrusions are not supplied with and end plates or assembly screws, these now need to be ordered separately. Acrylic end plates are also available which are ideal for any RF/Wi-Fi application, however we cannot guarantee any increase in signal capabilities. More details on accessories can be found below.

The extrusion is manufactured in Aluminium 6063 T6 (HE9). Silver anodised 5 μm thickness to BS 1615 - These can be painted directly if required. The interior and cut ends are not anodised. Black anodised 20 μm thickness, the interior and ends are anodised. The end plates are manufactured in Aluminium J57S or 5251 H22, the end plates are available in three finishes, black anodised, silver (clear) anodised or natural.

A new option of finish is now available with the Series 1 - 4 Enclosures, the pre-anodised black enclosure. With the pre-anodised black option all the internal surfaces and ends are bare aluminium, only the external surfaces (excluding ends) are anodised black. This option has full customisation options as stated below, but please bear in mind any holes/slots will have a silver rim around the ends of the cut outs. The main benefits of this option is a faster delivery time (a large stock of extrusion is kept at the factory, which is cut down to order) and also a slight decrease in price than purchasing a fully anodised black extrusion. For more information please contact us.

Accessories for the Series 1 - 4 Enclosures include self tapping and thread forming screws, these need to be ordered separately, we recommend silver screws with silver and blue enclosures, and black screws with the black and red enclosures. ABS End Bezels are supplied with 4 screw cap covers to prevent misuse or damage from impacts and falls, the end bezel also gives the enclosure a more elegant and appealing product finish. The bezels are only available in black and are supplied with 1 bezel and 4 screw cap covers. Aluminium mounting brackets are used to secured the enclosure to any surface, these are installed by simply removing at least one end plate and slots into the grooves on the external surface. The aluminium mounting brackets are available in 4 standard colours black, blue, red and silver. whilst they are available in 40mm and 80mm lengths. The brackets can be customised contact us for more information. ABS Mounting Lugs are also available, these simply snap on and off of the side of the enclosure, meaning no end plates need to be removed. This system is ideal for products where they are continually mounted and de-mounted during the products working life. The ABS mounting lugs are only available in black with a length of 40mm. Aluminium and Acrylic end plates are available, these also have to be ordered separately, both the aluminium and acrylic end plates are available with full customisation options as stated below. The acrylic end plates are ideal for any RF/Wi-Fi applications but we cannot guarantee any increased signal capabilities, we still recommend an antenna for full signal coverage. More details on colour options for end plates can be found below in the product accessories area. Sealing Kits are available to offer either IP65 or IP66 rating depending on whether the plastic washers are used. The sealing kits are supplied as a complete set, 2 seals and 8/10 washers, these are available in either black or white. Aluminium carrier plates are available to ensure a safe fit for any narrow PC Boards, these are fully customised to meet the PC Board requirements and are available with a minimum order quantity of 1 piece, these are only available in a rough silver aluminium finish. Protective rubber feet complete the product accessory range, allowing a little more protection when placed on any surface, with colours options of black and grey.

KGA Enclosures offers a full customisation service on both the extrusion and end plates (either aluminium or acrylic). Milling services or punching of holes into either the end plates or extrusions to meet all connector and access requirements. Printing and laser engraving services allows for the addition of text and graphics onto all product surfaces, enabling the end user to easily identify the products and this also gives the product a more elegant finish. These services are offered at very competitive pricing and with low minimum order quantities. To see how KGA Enclosures could help you with your current/next project simply email your technical drawings to or call 01535 636856 for a free no obligations quote. Please note payment terms do differ when products are customised.

Custom Extrusions Lengths are available with the Series 1 - 4 Enclosure Range.
Note - Extrusions are now sold individually. End Plates & Screws need to be ordered separately.
Ask us about Acrylic End Plates. Ideal for any RF/Wi-Fi application project.
PVC Labels & Metal Name Plates are available all customised to meet your requirements.
Switch to mm
Switch to Inches
Series 1 - 4 Extrusion Product Dimensions & Colour Options
Product Series Length Options Width Height More Information
Series 1 Enclosures 40mm 80mm 120mm 63.5mm 30mm 1.57" 3.15" 4.72" 2.50" 1.18" Read More ....
Series 2 Enclosures 80mm 160mm 220mm 108.5mm 30mm 3.15" 6.30" 8.66" 4.27" 1.18" Read More ....
Series 3 Enclosures 80mm 160mm 220mm 108.5mm 45mm 3.15" 6.30" 8.66" 4.27" 1.77" Read More ....
Series 4 Enclosures 80mm 160mm 220mm 169.8mm 53.5mm 3.15" 6.30" 8.66" 6.69" 2.11" Read More ....
Series 1 - 4 Enclosures PCB Dimensions
  Max P.C. Board Width Max P.C. Board Width for Components Max P.C. Board Height for Components
1 55mm 50mm 18mm - 20mm
2 100mm 95mm 18mm - 20mm
3 100mm 95mm 33mm
4 160mm 155mm 40mm
Remember Carrier Plates are available
Series 1 - 4 Enclosures Customisation Services
Customisation Services Extrusion End Plates
Milled Holes Yes Yes
Punched Holes No Yes
Colour Anodisation Yes Yes
Printed Text Yes Yes
Other Options Custom Lengths Milled From Solid

Follow us on LinkedIn UK Business Number - 09341700  -  VAT Registration Number - GB 204612745 Follow us on Twitter